How to unfasten electrical subpanel attached with ramset The Next CEO of Stack OverflowTips for removing drywall from bottom of closet headerWhat type of wire for subpanel in attached garage?Am I likely to be able to run a circuit from this panel for an EV charger?Basement leak behind electrical panelelectrical service to a shipping container workshopSafest way of temporarily working with a failed 4-wire outbuilding subpanel (one missing hot leg, neutral bonded ground on both ends)?What are good uses for tandem (double-stuff) breakers?no ground bar in electrical subpanelElectrical design for a house with an ADU, solar, and backup generatorTemporarily relocating an electrical panel while rebuilding a room
Avoiding the "not like other girls" trope?
Mathematica command that allows it to read my intentions
How do I keep Mac Emacs from trapping M-`?
Is it OK to decorate a log book cover?
How can the PCs determine if an item is a phylactery?
How seriously should I take size and weight limits of hand luggage?
How to implement Comparable so it is consistent with identity-equality
Why did Batya get tzaraat?
Can a PhD from a non-TU9 German university become a professor in a TU9 university?
Calculate the Mean mean of two numbers
Noise during hard braking
Why did early computer designers eschew integers?
Find the majority element, which appears more than half the time
Ising model simulation
Gauss' Posthumous Publications?
Finitely generated matrix groups whose eigenvalues are all algebraic
Man transported from Alternate World into ours by a Neutrino Detector
Why does freezing point matter when picking cooler ice packs?
Cannot restore registry to default in Windows 10?
How do I secure a TV wall mount?
Is it reasonable to ask other researchers to send me their previous grant applications?
It it possible to avoid kiwi.com's automatic online check-in and instead do it manually by yourself?
Read/write a pipe-delimited file line by line with some simple text manipulation
Is there a rule of thumb for determining the amount one should accept for of a settlement offer?
How to unfasten electrical subpanel attached with ramset
The Next CEO of Stack OverflowTips for removing drywall from bottom of closet headerWhat type of wire for subpanel in attached garage?Am I likely to be able to run a circuit from this panel for an EV charger?Basement leak behind electrical panelelectrical service to a shipping container workshopSafest way of temporarily working with a failed 4-wire outbuilding subpanel (one missing hot leg, neutral bonded ground on both ends)?What are good uses for tandem (double-stuff) breakers?no ground bar in electrical subpanelElectrical design for a house with an ADU, solar, and backup generatorTemporarily relocating an electrical panel while rebuilding a room
I'm getting ready to frame out a wall in my basement that has an electrical subpanel. I would like to move the panel out an inch or so, so I can frame around it and it will be flush with the finished wall. There is plenty of room and extra cable above so that I shouldn't need to rewire anything. My original plan was to remove cover, frame around it, turn off power, unscrew panel and slide it forward, reattach to studs, replace cover, turn power back on. But, the builders attached it with a ramset directly to the concrete! So, does anyone have any ideas on how to get that thing removed without having to disconnect all of the wiring to get a prybar in there? There might be enough clearance to get a sawsall blade behind the box and cut the nails from there, but I wouldn't bet on it. Any other ideas would be much appreciated.
electrical-panel fastener metal-cutting
edited 1 hour ago
isherwood
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I'm getting ready to frame out a wall in my basement that has an electrical subpanel. I would like to move the panel out an inch or so, so I can frame around it and it will be flush with the finished wall. There is plenty of room and extra cable above so that I shouldn't need to rewire anything. My original plan was to remove cover, frame around it, turn off power, unscrew panel and slide it forward, reattach to studs, replace cover, turn power back on. But, the builders attached it with a ramset directly to the concrete! So, does anyone have any ideas on how to get that thing removed without having to disconnect all of the wiring to get a prybar in there? There might be enough clearance to get a sawsall blade behind the box and cut the nails from there, but I wouldn't bet on it. Any other ideas would be much appreciated.
electrical-panel fastener metal-cutting
edited 1 hour ago
isherwood
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
I'm getting ready to frame out a wall in my basement that has an electrical subpanel. I would like to move the panel out an inch or so, so I can frame around it and it will be flush with the finished wall. There is plenty of room and extra cable above so that I shouldn't need to rewire anything. My original plan was to remove cover, frame around it, turn off power, unscrew panel and slide it forward, reattach to studs, replace cover, turn power back on. But, the builders attached it with a ramset directly to the concrete! So, does anyone have any ideas on how to get that thing removed without having to disconnect all of the wiring to get a prybar in there? There might be enough clearance to get a sawsall blade behind the box and cut the nails from there, but I wouldn't bet on it. Any other ideas would be much appreciated.
electrical-panel fastener metal-cutting
edited 1 hour ago
isherwood
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
I'm getting ready to frame out a wall in my basement that has an electrical subpanel. I would like to move the panel out an inch or so, so I can frame around it and it will be flush with the finished wall. There is plenty of room and extra cable above so that I shouldn't need to rewire anything. My original plan was to remove cover, frame around it, turn off power, unscrew panel and slide it forward, reattach to studs, replace cover, turn power back on. But, the builders attached it with a ramset directly to the concrete! So, does anyone have any ideas on how to get that thing removed without having to disconnect all of the wiring to get a prybar in there? There might be enough clearance to get a sawsall blade behind the box and cut the nails from there, but I wouldn't bet on it. Any other ideas would be much appreciated.
electrical-panel fastener metal-cutting
electrical-panel fastener metal-cutting
edited 1 hour ago
isherwood
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 1 hour ago
isherwood
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
edited 1 hour ago
isherwood
50.9k460129
edited 1 hour ago
isherwood
50.9k460129
edited 1 hour ago
isherwood
50.9k460129
50.9k460129
asked 2 hours ago
CropdusterCropduster
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
asked 2 hours ago
CropdusterCropduster
1161
asked 2 hours ago
CropdusterCropduster
1161
1161
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
New contributor
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
Cropduster is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.
add a comment |
add a comment |
2 Answers
2
active
oldest
votes
Powder-actuated gun nails are extremely hard. You don't want to have to cut them with a saw, and you probably won't have room anyway.
Get yourself an angle grinder with an abrasive wheel. Bracing your hands well against the box, carefully grind away just the heads of the nails. You should then be able to pull the box off the nail shafts.
Obviously, take all necessary precautions when working around electrical current, and use eye and ear protection.
Caveat: Be sure that you have enough length available on your primary conductors to make the move you have planned. You may also be required to install conduit behind the box, where the wires are exposed.
answered 1 hour ago
isherwoodisherwood
50.9k460129
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
add a comment |
You could drill around it with a 3/8 hole saw with the pilot bit removed, even a 1/4" might work. Don't push too hard on the washer so it doesn't come free. If it does come free drill a hole in it off to the side and insert a nail to stop it from turning. Dremil is expensive if you don't already have one and could take a while. A grinder is a little cumbersome working in a panel. All will work just adding some options.
answered 24 mins ago
Joe FalaJoe Fala
4,925328
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
add a comment |
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "73"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Cropduster is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f161172%2fhow-to-unfasten-electrical-subpanel-attached-with-ramset%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
Powder-actuated gun nails are extremely hard. You don't want to have to cut them with a saw, and you probably won't have room anyway.
Get yourself an angle grinder with an abrasive wheel. Bracing your hands well against the box, carefully grind away just the heads of the nails. You should then be able to pull the box off the nail shafts.
Obviously, take all necessary precautions when working around electrical current, and use eye and ear protection.
Caveat: Be sure that you have enough length available on your primary conductors to make the move you have planned. You may also be required to install conduit behind the box, where the wires are exposed.
answered 1 hour ago
isherwoodisherwood
50.9k460129
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
add a comment |
Powder-actuated gun nails are extremely hard. You don't want to have to cut them with a saw, and you probably won't have room anyway.
Get yourself an angle grinder with an abrasive wheel. Bracing your hands well against the box, carefully grind away just the heads of the nails. You should then be able to pull the box off the nail shafts.
Obviously, take all necessary precautions when working around electrical current, and use eye and ear protection.
Caveat: Be sure that you have enough length available on your primary conductors to make the move you have planned. You may also be required to install conduit behind the box, where the wires are exposed.
answered 1 hour ago
isherwoodisherwood
50.9k460129
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
add a comment |
Powder-actuated gun nails are extremely hard. You don't want to have to cut them with a saw, and you probably won't have room anyway.
Get yourself an angle grinder with an abrasive wheel. Bracing your hands well against the box, carefully grind away just the heads of the nails. You should then be able to pull the box off the nail shafts.
Obviously, take all necessary precautions when working around electrical current, and use eye and ear protection.
Caveat: Be sure that you have enough length available on your primary conductors to make the move you have planned. You may also be required to install conduit behind the box, where the wires are exposed.
answered 1 hour ago
isherwoodisherwood
50.9k460129
Powder-actuated gun nails are extremely hard. You don't want to have to cut them with a saw, and you probably won't have room anyway.
Get yourself an angle grinder with an abrasive wheel. Bracing your hands well against the box, carefully grind away just the heads of the nails. You should then be able to pull the box off the nail shafts.
Obviously, take all necessary precautions when working around electrical current, and use eye and ear protection.
Caveat: Be sure that you have enough length available on your primary conductors to make the move you have planned. You may also be required to install conduit behind the box, where the wires are exposed.
answered 1 hour ago
isherwoodisherwood
50.9k460129
answered 1 hour ago
isherwoodisherwood
50.9k460129
answered 1 hour ago
isherwoodisherwood
50.9k460129
answered 1 hour ago
isherwoodisherwood
50.9k460129
50.9k460129
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
add a comment |
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
1
1
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
A dremel with a cutoff wheel might be easier. Make sure to clean out all the metal filings prior to reenergising.
– Ed Beal
1 hour ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
You'd go through a good many cutoff wheels to get through those fat heads unless there's a gap underneath to get at the shaft. Still, not a bad idea, especially where space is tight.
– isherwood
14 mins ago
add a comment |
You could drill around it with a 3/8 hole saw with the pilot bit removed, even a 1/4" might work. Don't push too hard on the washer so it doesn't come free. If it does come free drill a hole in it off to the side and insert a nail to stop it from turning. Dremil is expensive if you don't already have one and could take a while. A grinder is a little cumbersome working in a panel. All will work just adding some options.
answered 24 mins ago
Joe FalaJoe Fala
4,925328
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
add a comment |
You could drill around it with a 3/8 hole saw with the pilot bit removed, even a 1/4" might work. Don't push too hard on the washer so it doesn't come free. If it does come free drill a hole in it off to the side and insert a nail to stop it from turning. Dremil is expensive if you don't already have one and could take a while. A grinder is a little cumbersome working in a panel. All will work just adding some options.
answered 24 mins ago
Joe FalaJoe Fala
4,925328
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
add a comment |
You could drill around it with a 3/8 hole saw with the pilot bit removed, even a 1/4" might work. Don't push too hard on the washer so it doesn't come free. If it does come free drill a hole in it off to the side and insert a nail to stop it from turning. Dremil is expensive if you don't already have one and could take a while. A grinder is a little cumbersome working in a panel. All will work just adding some options.
answered 24 mins ago
Joe FalaJoe Fala
4,925328
You could drill around it with a 3/8 hole saw with the pilot bit removed, even a 1/4" might work. Don't push too hard on the washer so it doesn't come free. If it does come free drill a hole in it off to the side and insert a nail to stop it from turning. Dremil is expensive if you don't already have one and could take a while. A grinder is a little cumbersome working in a panel. All will work just adding some options.
answered 24 mins ago
Joe FalaJoe Fala
4,925328
answered 24 mins ago
Joe FalaJoe Fala
4,925328
answered 24 mins ago
Joe FalaJoe Fala
4,925328
answered 24 mins ago
Joe FalaJoe Fala
4,925328
4,925328
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
add a comment |
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
I like this idea, but I wasn't aware that hole saws were made so small. The only ones I've seen are diamond-dust, intended for tile.
– isherwood
15 mins ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
Most of the quality holesaw bit sets only go down to 3/4 because of the arbour. I've got some unknown brand junky ones that go smaller. But even a 3/4 bit would do the trick, it'll just be harder to start without a pilot bit.
– Joe Fala
1 min ago
add a comment |
Cropduster is a new contributor. Be nice, and check out our Code of Conduct.
Cropduster is a new contributor. Be nice, and check out our Code of Conduct.
Cropduster is a new contributor. Be nice, and check out our Code of Conduct.
Cropduster is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Home Improvement Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fdiy.stackexchange.com%2fquestions%2f161172%2fhow-to-unfasten-electrical-subpanel-attached-with-ramset%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
